Tag Archives: 2

Colour matching issue for concrete

This question was asked by
Chris Helliwell

My drive laying company has gone out of business
I have a 260sq m area which does not match the colour of the more recently laid extra 60 and how much do you think it will cost to get the 260sq m recovered

The Solid colour stain was designed to colour large areas of concrete 1 uniform colour, if you combine this with the smartcolour (diluted) you will get the same 2 tone look that Imprinted concrete should have.

Take a look at the videos section at www.adsealcolours.co.uk this will give you some idea of what is involved.

Endura Solid Stain (ESS)

Smart Colour Stain (SMART)

Drew Palin

Concrete staining with smart colour

This question was asked by
Meriem

I would like to acid stain a concrete floor that has been grounded with 200 grit pads and densified, will the adseals smart color dye work on the concrete?

For the Smartcolour stains to work properly the concrete need to be porous enough for the stain to soak in. Please look at the videos section on www.adsealcolours.co.uk, the last video shows you what you need to look for in regards to the prep.

Drew Palin

Colouring and staining concrete table

This question was asked by
Sam Butler

I have recently made a concrete table for use inside. I was looking at possibly using your smart stain to make it a darker shade as it didn’t really come out as dark as I had liked. Wondered what it was like to use on new works. Also was looking at your polyeurethene gloss sealer. Was just looking for some advice really.

Yes the Smart colour will be ok to use and the High gloss PU will give a very nice gloss finish.

In regards to the prep work you will need to acid wash and profile the surface to remove any dusty material from the surface and to increase the porosity (there are a couple of videos on the website to show you what to look for when prepping the surface).

Smart Colour Stain (SMART)

Eco Acid [profiler] (EA)

High-gloss Polyurethane Sealer (HGPU)

Drew Palin

Sample kits

This question was asked by
Denise

I want to stain a large kitchen/hallway but not sure on colours do you do a sample kit?

Yes there are 4oz kits/bottles of each of the stains which are used as testers/samples available to purchase on our website.

www.adsealcolours.co.uk

Drew Palin

Cured concrete colour

This question was asked by
Mike thomas

i want to add some colour to some outside cured concrete on a roadway in a green or brown which would be the best product

It really all depends on what you are looking for as the finished product. If you are just looking for a solid uniform colour the the best one to use would be the Solid colour stain (link below), if you are wanting a more translucent or mottled colour or to have a few colours together then the Smartcolour would be best.

Solid Colour Stain (SOLID)

Smart Colour Stain (SMART)

Drew Palin

Staining/dying stone.

This question was asked by
Alison McKie

Hello, I have a natural blond sandstone hearth and wanted to check which of your products would be best for colouring it.

Unfortunately the stains and dyes that we sell are designed for use on concrete surfaces and not suitable for use on natural stone.

Drew Palin

Advice on stain colours

This question was asked by
Jon-Luke Kirton

We have a a large driveway (approx 200m2) with standard red block pavers. We would like to change the colour of these to a slate grey colour (we have a period character sandstone and traditional scottish slate house). What products would you recommend for this look to be achieved?

To completely change the colour of the paving is entirely doable, I have linked below the products you would need and if you check out the videos section you will find how to guides for the prep and the application.

Firstly you would need to remove any sealer that might be on the surface using either the Solstrip or Easystrip 1000 for acrylic sealers or the Easystrip 2000 if it is a Polyurethane sealer.

Once this is done you will need to profile the surface to make it porous to accept the stain then you would apply the Solid colour stain as a base colour, then a diluted Smartcolour to give the 2 tone antiqued effect.

After the stain has cured for 24 hours you will need to re apply a sealer coat.

Solid Colour Stain (SOLID)

Smart Colour Stain (SMART)

EasyStrip 1000 Coating Remover (ES1000)

Eco Acid [profiler] (EA)

Drew Palin

Solid colour or Smartcolour

This question was asked by
Ruth Beecham

I have 170 sq metres of brand new concrete interior residential floors. The aim was to acid stain these floors. However, your products look a whole stack easier! I have watched all your videos and read all the info, but am still a little confused with product names/ranges. The effect I want are pale base colours with slightly darker ‘faux’ effects on top. On the colour charts, I am confused by ‘solid’ colours and/or Smartcolour. (2 different colour cards side by side with different products listed?) Please could you explain the differences, and also send me the colour charts? Many thanks (and also for the preparation/water test video in particular).

In simple terms the Solid colour stain is a opaque stain, this is used to give the concrete one smooth uniform colour or a uniform base colour for the mottled or faux acid effect.

The Smart colour is a semi transparent finish and is used to add the mottled effect by sprayer.

Take a look at the video “staining concrete start to finish” this, I think, is what you are looking to do.

Drew Palin

Stain products

This question was asked by
John

Will this work on block paving.

Yes they will, they are ok to use on any concrete based product, just bear in mind that the coverage will be severely reduced, by at least half.

Drew Palin

Lightening up Imprint paving

This question was asked by
E.McKone

I have very dark almost black imprint and I hate it, can i make it lighter

Yes it is possible to make dark paving light,

First you would need to remove the sealer from the surface using the Easy strip (link below).

Once this has been done you need to jet wash the surface, then, when dry apply the Eco acid solution to profile the surface to ensure it is porous enough for the stain to soak in, there is a video on the website explaining this,

Next when it is dry (90% dry is fine) you can apply the Solid colour stain using the applicator brush following the instructions (included in the box and there is a video on the site).

If you are happy with the colour you can stop there.

If you want the 2 tone/antiqued effect of imprint concrete you can achieve this by using a darker Smartcolour diluted to 1:6 with water, all you have to do is spray an even coat all over the surface, then as it dries it will settle in the deeper areas to create the effect, as it is drying, if you think it is still to dark on the main surface, misting water over the surface will make more of the colour run off the high spots.

Once it has all dried (ideally 24hrs+) you will need to seal the drive using either the WB25 or WB34.

http://www.adsealcolours.co.uk/EasyStrip-1000-Coating-Remover.html

http://www.adsealcolours.co.uk/Solid-Colour-Stain.html

http://www.adsealcolours.co.uk/Smart-Colour-Stain.html

http://www.adsealcolours.co.uk/Eco-Acid-profiler.html

Drew Palin