Monthly Archives: March 2017

Delivery to Ireland

This question was asked by
Customer – AF

I’m wishing to purchase 2 x 25litres high solids sealer to be deliverd to Galway in Ireland, please could you advise me of the cost?

Good Morning,

Thank you for your enquiry, I can confirm we do ship to Ireland for £20.65 per drum

Kind regards

Jenni @ Adseal
Jenni Daley

Can I change the colour of my imprinted concrete?

This question was asked by
toby graham

Hello, I have an imprinted concrete driveway in terracotta. Is it possible to change the colour with one of your stain products

Yes it is totally possible to change the colour of your concrete.

You would first need to remove the old sealer using the Stripping solution (link below), then apply the Solid colour stain. If you want to just have it one colour then you can finish here by applying a sealer over the top.

If you are looking to give it the 2 tone look then Imprint should have you can apply a diluted coat of the smartcolour (a darker colour), allow to dry and then seal.

https://www.adsealcolours.co.uk/Solvent-Stripper-SolStrip.html

https://www.adsealcolours.co.uk/Solid-Colour-Stain.html

https://www.adsealcolours.co.uk/Smart-Colour-Stain.html
Drew Palin

Advice on sealant

This question was asked by
Lee

I’ve up-cycled the slate bedding from a snooker table, by using it as a a work top for a BBQ I built in the garden.
I was really pleased with my idea when I first installed it.
But it’s been a few years now and it’s looking a bit shabby, it’s gone grey and had moss forming on it.
So I have sanded it down and got rid of all the moss, but I want it to be glossy like when it was first installed.
Is there a product that would restore it to its shinny former state.
It looks great in the rain, but when it dries it returns to a dull grey finish.

As you are looking for a glossy finish, I would recommend using the High gloss PU (link below) this will give you a good glossy finish (like when it is wet) and it is a very hard wearing resin so it will last many, many years before it would need re coating.

https://www.adsealcolours.co.uk/High-Gloss-Polyurethane-Sealer.html
Drew Palin

What is the best way to stain a cement wall?

This question was asked by
Proinsias

Hello. I have put an inch thick cement coat on top of a block wall and have carved out the cement to imitate real stone shapes. I would like to add a realistic mottled stone finish to imitate grey limestone or slate. Can I apply your product by hand-brush? Would your translucent range be suitable/

Newlook do a specific stain for vertical surfaces called Wallstain (link below), if you use 3 or 4 different colours you can achieve a very nice natural looking wall.

https://www.adsealcolours.co.uk/WallStain-Solid-and-Translucent.html
Drew Palin

I have a piece of coloured imprinted concrete that I would like to clean and seal. What do you recommend I use?

This question was asked by
John Pascall

Imprinted concrete what do I clean and seal this with approx 30 sq. yards.

Hi John

Thank you for your enquiry.

To clean the paving you are best using a power washer, if there are any oil stains you can remove them using our surface degreaser (linked below).

Once clean and dry you can then apply the sealer (again linked below).

https://www.adseal.info/AdSeal-Super-for-block-paving-sealer-and-imprinted-concrete-sealer.html

https://www.adsealcolours.co.uk/Surface-Cleaner-Degreaser-and-Oil-Remover.html

Drew Palin

Concrete floor

This question was asked by
Simon Lysons

I’m looking to seal an internal concrete floor but want to end up with a shiny gloss finish
What product would you recommend

Many thanks
Simon

Hi Simon

Thank you for your enquiry.

If you are looking for a high gloss finish to the floor I would recommend using our High Gloss PU sealer (link below) this will give a nice gloss finish to any floor.

https://www.advancedsealingsolutions.co.uk/High-Gloss-PU.html

Drew Palin